Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
Everyone is bound to have their own assumption when it comes to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a new one is also a reasonably hard project. If the old bathtub is conveniently available, the project can relocate rapidly; if you have to open a wall surface to remove the old tub as well as position the new tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to leave the old tub and embeded in the brand-new one. See to it you have qualified on your own for the job as well as are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Possibilities are you may require an expert plumber to make tube links.
This write-up will help you install a new bath tub in your bathroom if you have actually already bought a new bathtub as well as don't need to alter the arrangement of your previous supply of water pipelines.
Your tools as well as product checklist need to make up the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. Once the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub until the spirit level reads level.
To install taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water as well as inspect all joints and brand-new pipework for leakages and tighten them if necessary. Load the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait until the bathtub has actually been utilized at the very least when as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the manufacturer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall between the bathroom and also the tiling, resulting in difficulties with dampness and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the activity experienced when the tub is in use. The sealant can fracture rather early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that editorial about Installing A Bathtub from a friend on a different web page. Enjoyed reading our write-up? Please share it. Help other people locate it. Thanks so much for going through it.
Seek immediate plumbing assistance now. Report this page